Ranch WD-12 24 36 48 Series Low Voltage High Current PWM Pulse Width Adjustable Speed Power Supply-WD Series-Permanent Magnet DC Motor_Boshan DC Motor Factory-Zibo Boshan Guanglian Motor Factory
Product Categories
contact us

Company Name: Zibo Boshan Guanglian Motor Factory Address: No. 5 Yingxiong Road, Boshan District, Zibo City Tel: 0533-4268767
Mobile phone: 13355233322 Mr. Zhao 13869356603 Manager Wang Contact: Zhao Hao Fax: 0533-4267117

WD series

WD-12 24 36 48 series low voltage and high current PWM pulse width speed regulating power supply



Market price: 0.00

Special price: 0.00

Product introduction:

系列低压大电流 PWM 脉宽调速电源是采用专用模块,控制和供电完全隔离,避免了低压大电流时对控制系统的干扰。 The WD-12 24 36 48 series low-voltage high-current PWM pulse-speed power supply produced by Boshan DC Motor Factory uses special modules, and the control and power supply are completely isolated to avoid interference with the control system during low-voltage and high-current. Its excellent linear ratio, wide voltage input range, outstanding performance and speed regulation ratio, with stable and reliable quality, make it widely used. This series of products are suitable for battery-powered or DC-powered field operations and low-voltage automatic control.

One, Main technical parameters and characteristics:

、输入电压: DC 12 24 36 48V 8 、采用脉宽调制技术、体积小、性能优 1. Input voltage: DC 12 24 36 48V 8. Using pulse width modulation technology, small size, excellent performance

、输出电压: DC 0---12 24 36 48V (相对于输入电压) 9 、电流设置和限制保护 2. Output voltage: DC 0 --- 12 24 36 48V (relative to input voltage) 9. Current setting and limit protection

、输出电流: DC 80A 10 、瞬时短路保护 3 , output current: DC 80A 10 , instantaneous short circuit protection

、给定方式:电位器 4.7KΩ/2W 11 、软启动 / 软停止功能 4. Setting method: Potentiometer 4.7KΩ / 2W 11. Soft start / soft stop function

、环境温度: --10 5. Ambient temperature: --10 . 60 C ~ + 60 . 12 、低速启动力矩大 C 12 , high starting torque at low speed

、环境湿度:相对湿度 80RH 6. Ambient humidity: relative humidity 80RH . 13 、可实现远程启停 (No condensation) 13 , remote start and stop

、适用于稀土、永磁和他励马达 7.Applicable to rare earth, permanent magnet and other excited motors

Second, the potentiometer speed description:

、电流限制调整: CUR 1. Current limit adjustment: CUR

120 %~ 200 Can limit the maximum output current of the drive board, adjust the potentiometer according to the rated current of the selected motor, so that the maximum output current of the drive board is 120 % to 200 % of the rated current of the motor

、转矩补偿调整: IR COMP 2. Torque compensation adjustment: IR COMP

电位器用于调整马达工作在不同的负载时,使其转速保持恒定。 IR COMP potentiometer is used to adjust the speed of the motor to keep constant when it works under different loads.

、最高输出电压调整: MAX 3. Maximum output voltage adjustment: MAX

12V--48V 之间 Adjust the potentiometer to determine the highest output voltage of the driver. The adjustment range is between 12V--48V .

three, Terminal description:

Vin + -:输入端(注:正、负极接线一定要正确,否则会烧毁调速器)。 1. Vin + -: Input terminal (Note: The positive and negative wiring must be correct, otherwise the governor will be burned).

Vout + -:电枢输出端 , 接马达电枢端。 2. Vout + -: Armature output end , connected to the motor armature end.

、控制信号输入端及起停控制:使用 4.7K 电位器调速,使用开关可以控制电源的起停。 3. Control signal input terminal and start-stop control: Use a 4.7K potentiometer to adjust the speed, and use a switch to control the start-stop of the power supply.

LED 指示灯说明: 4. LED indicator description:

RUN :工作指示灯(绿) 1. RUN : work indicator (green)

When the power output voltage is normal, this indicator is on

FAU :短路保护指示(红) 2. FAU : Short circuit protection indication (red)

“+OUT-”“ 输出端出现外部短路时,则驱动器会迅速停止输出,同时点亮 短路保护指示灯 When the driver's "+ OUT-" " external short circuit occurs at the output end, the driver will quickly stop output and light up " short circuit protection indicator

Hits: 2741 Entry time: 2014-03-18 10:44:55 [ Print this page ] [ Return ]